SATO SG112 ex Programming Reference Manual Download Page 497

Page: 497 / 516

496

Variable name

Setting range

Initial value (Factory setting)

DHCP protocol

ENABLE/DISABLE

DISABLE

Keepalive time

30 to 300

180 (seconds)

Keepalive retry

1 to 99

17 (times)

Socket cancel

Normal/Compatible

Normal

ROOT password

Any alphanumeric [16]

NULL (no password)

IPv6 address

0000:0000:0000:0000:0000:0000:0000:

0000 to

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF

0000:0000:0000:0000:0000:0000:0000:

0000

IPv6 prefix

0 to 128

IPv6 default router

0000:0000:0000:0000:0000:0000:0000:

0000 to

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF

0000:0000:0000:0000:0000:0000:0000:

0000

IPv6 address

resolve

MANUAL/DHCP/AUTO

AUTO

*1 Numbers in [ ] are upper limit.

SNMP (Simple Network Management Protocol)

SNMP Agent that supports UDP/IP, IPX and manages a range of printer information is implemented.

SNMPv2 which is based on the RFC 1902 - RFC 1908 is supported.

About errors:
They are assigned to "hrPrinterDetectedErrorState" object of Host Resources MIB Printer Status.

Error state

Bit number

Error state of this product

lowPaper

noPaper

Paper End

lowToner

Ribbon Near End

noToner

Ribbon End

doorOpen

Head Open

jammed

offline

Offline

serviceRequested

inputTrayMissing

outputTrayMissing

markerSupplyMissing

outputNearFull

outputFull

inputTrayEmpty

overduePreventMaint

* Errors that are not mentioned in the above table are assigned to Alert Group.

Summary of Contents for SG112 ex





































































































































































































































































































































































































































































































































Search results

Summary of Contents for SG112 ex

Reviews:

Brands by name

Popular brands

SATO SG112 ex, Programming Reference Manual

Search results

Summary of Contents for SG112 ex

Reviews:

Brands by name

Popular brands