manualshive.com logo in svg

SATO SG112 ex, Programming Reference Manual

Share
Download
SATO SG112 ex Programming Reference Manual Download Page 479

478

IEEE1284

Basic Specifications

This interface complies with Centronics/IEEE1284 standard. Single item receive or multiple receive

can be switched on the interface mode of the printer.

Interface

Protocol

Status4, Status5
Refer to Communication protocol for details.

Connector

Product side: Amphenol 36 pin (Female)
Cable side: Amphenol 36 pin (Male)

Cable Length

Equal to or less than 1.5 m

Signal Level

High level: +2.4 to +5.0 V
Low level: +0.0 to +0.4V

Recieve Mode

Single item receive
Multiple buffer
buffer mode available by the interface mode of this product.

Receive Buffer Size

2.95 MB

Summary of Contents for SG112 ex





































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands