manualshive.com logo in svg

SATO SG112 ex, Programming Reference Manual

Share
Download
SATO SG112 ex Programming Reference Manual Download Page 458

457

XON/XOFF

This communication protocol communicates with the host to see if this product is ready to receive

data by sending "XON" (HEX 11H) or "XOFF" (HEX 13H) codes to SD line. Single item receive and

multiple buffer can be switched in the interface mode of this product.
When the print data (STX <A> ~ <Z> ETX) has been sent from the host in the conditions below,

received data may not be accurate:
1) When this product is in offline state.
2) When an error has occurred in this product.

Connection diagram

1) DB-9P 

This product

Host

RD 

2 

 

3 

SD 

SD 

3 

 

2 

RD 

SG 

5 

 

5 

SG 

　

IMPORTANT: Depending on the host used, it may need to loop CS and RS (constantly maintain at “High” level) on the host

side. For more details, refer to your host computer documentation.

I/O signal

Pin no.

Signal

name

I/O

Contents

2

RD

Input

Data transferred from the host to this product

3

SD

Output

Data transferred from this product to the host

5

SG

-

Signal ground

Summary of Contents for SG112 ex





































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands