SATO SG112 ex Programming Reference Manual Download Page 459

Page: 459 / 516

458

Timing chart of single item receive

1) Normal process

2) Error process

Printer Status

Note: the printer will be polled by XON at intervals of 500 msec from the initializing to the first data reception.

Printer

Power On

Initializing

STX.ETX (2)

Receive/Analysis/Edit (2)

Printing (1)

Online

Offline

Printing (2)

Press the LINE key

Receive/Analysis/Edit (1)

STX.ETX (1)

XON

XOFF

XON

500 msec

XOFF

Online

Printer Status

Printer

Printing (1)

Online

Head open

Paper end error

Offline

Press the LINE key

Receive/Analysis/Edit (1)

STX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ETX (1)

Printing (2)

XON

XOFF

XON

Head close

Press the LINE key

When the paper end error occurs, open the head, set label, close the head and feed.

Note: (1) The paper end error will be released when the head is closed.

(2) XOFF will be sent when data is received during an error.

XOFF

Online

Offline

Summary of Contents for SG112 ex





































































































































































































































































































































































































































































































































Search results

Summary of Contents for SG112 ex

Reviews:

Brands by name

Popular brands

SATO SG112 ex, Programming Reference Manual

Search results

Summary of Contents for SG112 ex

Reviews:

Brands by name

Popular brands