manualshive.com logo in svg

Ricoh MP C305SPF, Field Service Manual, Page: 90 / 146

Share
Download
Ricoh MP C305SPF Field Service Manual Download Page 90

0

Printing while a paper cassette is
pulled out, when the Just Size
Printing feature is enabled.
0: Printing will not start
1: Printing will start if another
cassette has a suitable size of
paper, based on the paper size
selection priority tables.

Cross reference
Just size printing on/off – User switch 05, bit 5

1-7

Not used.

Do not change the settings.

Printer Switch 07 (SP No. 1-103-008)

No

Function

Comments

0-3

Not used.

Do not change the settings.

4

List of destinations in the
Communication Failure Report for
broadcasting
0: All destinations
1: Only destinations where
communication failure occurred

1: Only destinations where communication failure
occurred are printed on the Communication Failure
Report.

5-7

Not used.

Do not change the settings.

Printer Switch 08 - Not used (do not change the settings)

Printer Switch 09 - Not used (do not change the settings)

Printer Switch 0A - Not used (do not change the settings)

Printer Switch 0B - Not used (do not change the settings)

Printer Switch 0C - Not used (do not change the settings)

Printer Switch 0D - Not used (do not change the settings)

Printer Switch 0E (SP No. 1-103-015)

No

Function

Comments

4. Service Tables

88

Summary of Contents for MP C305SPF



















































































































































Reviews:

No comments