manualshive.com logo in svg

Ricoh MP C305SPF, Field Service Manual, Page: 101 / 146

Share
Download
Ricoh MP C305SPF Field Service Manual Download Page 101

0
1

Monitor speaker during communication (tx
and rx)

(0, 0): The monitor speaker is disabled all
through the communication.
(0, 1): The monitor speaker is on up to phase B in
the T.30 protocol.
(1, 0): Used for testing. The monitor speaker is on
all through the communication. Make sure that
you reset these bits after testing.

Bit 1

Bit 0

Setting

0

0

Disabled

0

1

Up to Phase B

1

0

All the time

1

1

Not used

2

Monitor speaker during memory
transmission
0: Disabled 1: Enabled

1: The monitor speaker is enabled during memory
transmission.

3-5 Not used

Do not change the settings.

6

G3 mode selection for direct line
0: Off
1:On

1: G3 communication through the direct line is
enabled.

7

Not used

Do not change the settings.

G3 Switch 01 (SP No. 1-105-002)

No

Function

Comments

0-3 Not used

Do not change the settings.

4

DIS frame length
0: 10 bytes 1: 4 bytes

1: The bytes in the DIS frame after the 4th byte will not
be transmitted (set to 1 if there are communication
problems with PC-based faxes which cannot receive the
extended DIS frames).

5

Not used

Do not change the setting.

6

Forbid CED/AMsam output
0: Off
1: On (Forbid output)

Do not change this setting (Default: 0: Off), unless
communication problem is caused by a CED or ANSam
transmission.

7

Not used

Do not change the setting.

Bit Switches

99

Summary of Contents for MP C305SPF



















































































































































Reviews:

No comments