manualshive.com logo in svg

Ricoh MP C305SPF, Field Service Manual, Page: 124 / 146

Share
Download
Ricoh MP C305SPF Field Service Manual Download Page 124

Address

Function

Unit

Remarks

68053F

Country dial tone upper frequency limit
(HIGH)

Hz (BCD)

If both addresses contain
FF(H), tone detection is
disabled.

680540

Country dial tone upper frequency limit
(LOW)

680541

Country dial tone lower frequency limit
(HIGH)

If both addresses contain
FF(H), tone detection is
disabled.

680542

Country dial tone lower frequency limit
(LOW)

680543

Country dial tone detection time

20 ms

If 680543 contains FF, the
machine pauses for the
pause time (680548 /
680549).

680544

Country dial tone reset time (LOW)

680545

Country dial tone reset time (HIGH)

680546

Country dial tone continuous tone time

-

-

680547

Country dial tone permissible drop time

20 ms

-

680548

Country dial wait interval (LOW)

680549

Country dial wait interval (HIGH)

68054A

Time between opening or closing the
DO relay and opening the OHDI relay

1 ms

See Notes 3, 6 and 8.
SP2-103-012 (parameter
11).

68054B

Break time for pulse dialing

1 ms

See Note 3.
SP2-103-013 (parameter
12).

68054C

Make time for pulse dialing

1 ms

See Note 3.
SP2-103-014 (parameter
13).

68054D

Time between final OHDI relay closure
and DO relay opening or closing

1 ms

See Notes 3, 6 and 8.
SP2-103-015 (parameter
14).
This parameter is only valid
in Europe.

4. Service Tables

122

Summary of Contents for MP C305SPF



















































































































































Reviews:

No comments