manualshive.com logo in svg

Ricoh MP C305SPF, Field Service Manual, Page: 139 / 146

Share
Download
Ricoh MP C305SPF Field Service Manual Download Page 139

No

FUNCTION

COMMENTS

0

Original width of e-mail
attachment: A4
0: Off
1: On

Sets the original width of the e-mail attachment as A4.

1

Original width of e-mail
attachment: B4
0: Off
1: On

Sets the original width of the e-mail attachment as B4.

2

Original width of e-mail
attachment: A3
0: Off
1: On

Sets the original width of the e-mail attachment as A3.

3-6

Not used

Do not change these settings.

7

Designates the bits to
reference for original size of
e-mail attachments
0: Registered (Bit 0 to 6)
1: No registration.

The "0" selection (default) references the settings for Bits 00,
01, 02 above. The "1" selection ignores the selections of
Bits 00, 01, 02.

Switch 02

No

FUNCTION

COMMENTS

0

Line resolution of e-mail
attachment: 200 x 100
0: Off
1: On

Sets the line resolution of the e-mail attachment as 200
x100.

1

Line resolution of e-mail
attachment: 200 x 200
0: Off
1: On

Sets the line resolution of the e-mail attachment as 200 x
200.

Dedicated Transmission Parameters

137

Summary of Contents for MP C305SPF



















































































































































Reviews:

No comments