manualshive.com logo in svg

Ricoh MP C305SPF, Field Service Manual, Page: 66 / 146

Share
Download
Ricoh MP C305SPF Field Service Manual Download Page 66

6

Protocol dump list output after each
communication
0: Off
1: On

This is only used for communication troubleshooting. It
shows the content of the transmitted facsimile protocol
signals. Always reset this bit to 0 after finishing testing.
If system switch 09 bit 6 is at "1", the list is only
printed if there was an error during the
communication.

7

Not used

Do not change the setting.

G3 Communication Parameters

Modem rate

336: 33600 bps 168: 16800 bps
312: 31200 bps 144: 14400 bps
288: 28800 bps 120: 12000 bps
264: 26400 bps 96: 9600 bps
240: 24000 bps 72: 7200 bps
216: 21600 bps 48: 4800 bps
192: 19200 bps 24: 2400 bps

Resolution

S: Standard (8 x 3.85 dots/mm)
D: Detail (8 x 7.7 dots/mm)
F: Fine (8 x 15.4 dots/mm)
SF: Superfine (16 x 15.4 dots/mm)
21: Standard (200 x 100 dpi)
22: Detail (200 x 200 dpi)
44: Superfine (400 x 400 dpi)

Compression mode

MMR: MMR compression
MR: MR compression
MH: MH compression
JBO: JBIG compression (Optional mode)
JBB: JBIG compression (Basic mode)

Communication mode

ECM: With ECM
NML: With no ECM

4. Service Tables

64

Summary of Contents for MP C305SPF



















































































































































Reviews:

No comments