Regency Grandview G600C Owners & Installation Manual Download Page 86

Page: 86 / 104

Grandview

G600C Gas Fireplace

installation

Safety Screen Removal

1. Slide screen

up.

2. Slide screen

right.

3. Lower screen

down.

4. Swing screen

outwards while
keeping the
screen level
and remove.

To install the safety screen

—Reverse steps above.

Safety Screen Installation

Glass Door Removal

To install the door

—Reverse steps above.

1. To remove the glass door - place both hands on either side of

the latch. Pull forward then up to unlock, repeat on opposite
side.

Important: After releasing the latches, support the weight of the

door.

2. With both latches released, support the door with both hands

and tilt out to approximately a 60 degree angle.

3. Lift the door up and out of lower slots to remove.

Glass Door Installation

Latch locations

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands