Regency Grandview G600C Owners & Installation Manual Download Page 85

Page: 85 / 104

installation

Grandview

G600C Gas Fireplace

11.25.19

920-192

G800C

OPTIONAL ON/OFF REMOTE KIT INSTALLATION

1. Connect the supplied speed control switch and unit receptacle to

the 120V mains power supply by following the wiring diagram as
shown.

An optional on/off remote and receiver may be installed in the unit.

2. Install 4 x AA batteries into the remote receiver and 3 x AAA

batteries into the remote control.

3. Locate the black wire running from the valve to the unit on/off

switch. Unclip the wire holder clip and remove the black wire from
the clip.

4. Break the connection between the inline wire connectors on the

black wire.

5. Connect the two connectors on the black wire to the two wires

from the remote receiver, as shown.

6. Put the receiver in position in the holder bracket beneath the

firebox, to the right of the DC Sparker and Fan Speed Control
Module (if installed). Secure with supplied velcro strips.

7. Tidy the wires together and secure wires back into the wire hold-

er clip.

NOTE: The remote receiver may be installed as a wall

mounted switch if required. A wall mount cover
plate is provided with the receiver. See instruc-
tions in this manual for Installing an Optional Wall
Switch of Thermostat.

Optional On/Off Remote Kit Installation (Part # 761-976)

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands