Regency Grandview G600C Owners & Installation Manual Download Page 39

Page: 39 / 104

installation

Grandview

G600C Gas Fireplace

Finishing Trim Install (Part # 776-928)

08.06.20

920-298

FINISHING TRIM INSTALLATION

G600EC/G600C

The finishing trim can be installed to upgrade the look of the
fireplace or to cover facing material edges.

1. Lay the parts on a soft surface, painted side down.
2. Insert the tab on the left side in to the slot on the top.
3. Fold the tabs down to secure.
4. Insert the tab on the top into the slot on the right.
5. Fold the tab down to secure.

08.28.19

920-151

FINISHING TRIM INSTALLATION

The Finishing Trim can be installed to upgrade the look of the fi replace
or to cover facing material edges.

1. Lay the parts on a soft surface painted side down.

2. Insert the tab on the left side into the slot on the top.

3. Fold the tabs down to secure.

4. Insert the tab on the top into the slot on the right.

5. Fold the tab down to secure.

Right Side

Finishing Trim Install Instructions:

1. Bend the four tabs on the outer box front forward. There are two tabs per side.

These tabs are the mounts for the faceplate or fi nishing trim.

2. Bend the two tabs on the top nailing fl ange down.

3. Bend the tabs on the left and right nailing fl anges forward. There are two tabs

per nailing fl ange.

Top and Side Nailing Flange Tabs

See section: N

AILING

LANGE

NSTALL

FOR

AILING

LANGE

EPTH

SETTINGS

Left Side

See section: Nailing Flange Install for Nailing Flange Depth
Settings.

Finishing Trim Install Instructions:

1. Bend the four tabs on the outer box front forward. There are two

tabs per side. These tabs are the mounts for the faceplate or
finishing trim.

2. Bend the two tabs on the top nailing flange down.
3. Bend the tabs on the left and right nailing flages forward. There

are two tabs per nailing flange.

08.28.19

920-151

FINISHING TRIM INSTALLATION

The Finishing Trim can be installed to upgrade the look of the fi replace
or to cover facing material edges.

1. Lay the parts on a soft surface painted side down.

2. Insert the tab on the left side into the slot on the top.

3. Fold the tabs down to secure.

4. Insert the tab on the top into the slot on the right.

5. Fold the tab down to secure.

Right Side

Finishing Trim Install Instructions:

1. Bend the four tabs on the outer box front forward. There are two tabs per side.

These tabs are the mounts for the faceplate or fi nishing trim.

2. Bend the two tabs on the top nailing fl ange down.

3. Bend the tabs on the left and right nailing fl anges forward. There are two tabs

per nailing fl ange.

Top and Side Nailing Flange Tabs

See section: N

AILING

LANGE

NSTALL

FOR

AILING

LANGE

EPTH

SETTINGS

Left Side

08.28.19

920-151

FINISHING TRIM INSTALLATION

The Finishing Trim can be installed to upgrade the look of the fi replace
or to cover facing material edges.

1. Lay the parts on a soft surface painted side down.

2. Insert the tab on the left side into the slot on the top.

3. Fold the tabs down to secure.

4. Insert the tab on the top into the slot on the right.

5. Fold the tab down to secure.

Right Side

Finishing Trim Install Instructions:

1. Bend the four tabs on the outer box front forward. There are two tabs per side.

These tabs are the mounts for the faceplate or fi nishing trim.

2. Bend the two tabs on the top nailing fl ange down.

3. Bend the tabs on the left and right nailing fl anges forward. There are two tabs

per nailing fl ange.

Top and Side Nailing Flange Tabs

See section: N

AILING

LANGE

NSTALL

FOR

AILING

LANGE

EPTH

SETTINGS

Left Side

09.17.19

920-151

FINISHING TRIM INSTALLATION

08.28.19

920-151

FINISHING TRIM INSTALLATION

The Finishing Trim can be installed to upgrade the look of the fi replace
or to cover facing material edges.

1. Lay the parts on a soft surface painted side down.

2. Insert the tab on the left side into the slot on the top.

3. Fold the tabs down to secure.

4. Insert the tab on the top into the slot on the right.

5. Fold the tab down to secure.

Right Side

Finishing Trim Install Instructions:

1. Bend the four tabs on the outer box front forward. There are two tabs per side.

These tabs are the mounts for the faceplate or fi nishing trim.

2. Bend the two tabs on the top nailing fl ange down.

3. Bend the tabs on the left and right nailing fl anges forward. There are two tabs

per nailing fl ange.

Top and Side Nailing Flange Tabs

See section: N

AILING

LANGE

NSTALL

FOR

AILING

LANGE

EPTH

SETTINGS

Left Side

Top and Side Nailing Flange Tabs

G800EC/G800C

PART # 776-928

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands