Regency Grandview G600C Owners & Installation Manual Download Page 66

Page: 66 / 104

Grandview

G600C Gas Fireplace

installation

Brick Panel Installation (Part # 776-901, 776-903, 776-904, 776-905)

08.04.20

920-297

BRICK PANEL INSTALLATION

G600EC/G600C

5. Loosen screws and remove brick clip.

1. Remove screen and glass door, if installed.

2. Loosen two screws in locations shown below. Slide upper baffle

towards the back wall and then remove from unit.

6. Install the right side panel—the angled corner should be located

facing the bottom rear of the fireplace when installing.

NOTE:

Shorter row of bricks should be positioned at the bottom of
back and side panels.

7. With panel in position, secure it with the brick clip removed in step

5 and retighten screw.

Note: Do not install the firebed grate, media, vermiculite, embers,

and logs until the brick panels are installed.

• Brick panels will discolor a little during normal operation. This is

normal and should not be considered a defect.

3. Loosen 2 screws on pilot assembly in locations shown below.

Slide pilot shield towards the back of the unit and remove from
unit.

8. Repeat Steps 5-7 on the left side.

9. Slide the bottom panel carefully underneath the burner and

push to the back until it contacts the back panel.

4. Install back panel carefully. Tilt panel forward from the top and rest

the bottom of the panel on the firebox floor. Tip top back until it also
rests on the firebox back wall.

10. Reinstall the upper baffle.

11. Reinstall the pilot shield removed in step 3.

(PARTS # 776-901, 776-903, 776-904, 776-905)

tooltip

Item Part #

Description

N/A

Inside Top of Firebox

N/A

Panel

761-049 Brick Clip

904-519 Screw

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands