Regency Grandview G600C Owners & Installation Manual Download Page 18

Page: 18 / 104

Grandview

G600C Gas Fireplace

installation

Clearance / Framing and Venting Configurations

The G600C is designed to allow for unique installation options—depending on the desired finish.
Please review the options and follow the specific clearance, framing, and finishing options for that application.

The applications are as follows:

Cool Wall Installation-Clean Front & Outside Finish

: combustible materials can be installed right up to the fireplace opening with this option.

Non Combustible Installation-Clean Front & Outside Finish Applications:

non-combustible required when installing materials right to the fireplace

opening with this option.

See descriptive diagrams on the next page.

Note: The topics listed below can be found in the pages that follow.

Clearance / Framing and Venting Configurations .............................................................. 16

Cool Wall Installation (Combustible Finishing) ................................................................... 17

Non-Combustible Installation ............................................................................................. 17

Unit Assembly Prior to Installation (Nailing Flange Installation) ........................................ 18

Nailing Flange Installation ................................................................................................. 19

Cool Wall Clearances ........................................................................................................ 21

Cool Wall Mantel Clearances ............................................................................................ 22

Cool Wall Mantel Leg Clearances ..................................................................................... 22

Cool Wall Installation—Framing ......................................................................................... 23

Cool Wall Installation-Cool Wall Conversion ...................................................................... 24

Chase Venting ................................................................................................................... 25

Chase Vent Installation - Cool Wall (Part #776-941).......................................................... 26

Clean Front Installation (Non Cool Wall) - Clearances ...................................................... 27

Clean Front Installation (Non Cool Wall) - Mantel Clearances .......................................... 28

Clean Front Installation (Non Cool Wall) - Mantel Leg Clearances ................................... 29

Clean Front Installation (Non Cool Wall)—Non Combustible

Requirements .................................................................................................................. 29

Clean Front Installation—Framing (Non Cool Wall) ........................................................... 30

Clean Front Installation ...................................................................................................... 31

Outside Finish Installation (Non Cool Wall)—Clearances.................................................. 32

Outside Finish Installation (Non Cool Wall) - Mantel Clearances ...................................... 33

Outside Finish Installation (Non Cool Wall)—Mantel Leg

Clearances ...................................................................................................................... 33

Outside Finish Installation (Non Cool Wall)—Framing ....................................................... 34

Outside Finish—Finishing ................................................................................................. 35

Faceplate Installation (Part # 776-922, 776-924, 776-926) ............................................... 36

Finishing Trim Install (Part # 776-928) ............................................................................... 37

Wall Board/Drywall Installation .......................................................................................... 39

Conversion to Rear Vent .................................................................................................... 40

Vent Restrictor Installation ................................................................................................. 43

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands