Regency Grandview G600C Owners & Installation Manual Download Page 91

Page: 91 / 104

Grandview

G600C Gas Fireplace

maintenance

Removing Valve

12. Remove the 12 screws securing the valve tray

assembly in place (Diagram 6) and then lift out
entire assembly.

Shut off the gas and electrical supply.

2. Remove the safety screen.

3. Remove the glass door.

4. Remove the logs and glass.

5. Remove the log grate assembly by removing 2

screws and sliding tray forward to remove.

Diagram 1: Remove left and right screws.

Diagram 2

8. Remove 2 screws securing the fan access

(Diagram 3).

Diagram 3

Switch wires

Diagram 6

Replacing Thermocouple

1. Follow steps 1-13 for replacing valve.

2. Disconnect thermocouple at gas valve.

3. Disconnect thermocouple at pilot assembly end.

4. Replace thermocouple.

5. Reverse steps 1-13.

6. Remove lower (brick or enamel) panel.

7. Remove 3 screws securing the bruner and then

slide the burner assembly to the right to release
it from the orifice, then lift it out

10. Disconnect the two switch wires from the valve,

as shown below.

Valve Replacement

13. Remove Philips head screws securing DC

sparker box, as shown below.

11. Disconnect spark electrode from DC sparker

box, as shown below.

Diagram 5

Diagram 4

Diagram 7

9. Disconnect the inlet gas line.

Thermocouple

Electrode wire

Philips head screw

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands