Regency Grandview G600C Owners & Installation Manual Download Page 26

Page: 26 / 104

Grandview

G600C Gas Fireplace

installation

Cool Wall Installation-Cool Wall Conversion

1. Remove safety screen from unit as per manual.

2. Remove the three screws from the top of the unit, holding the top

cover in place.

3. Remove the top cover piece and secure it to the rear right

side of the unit with one screw as shown.

6. Remove the inner cover piece and secure it to the left rear side of the

unit with one screw as shown.

7. Loosen the two outermost screws which are accessed through the holes

in the locations show below. NOTE: Do not remove these two screws;
loosen them.

8. Reach underneath the top of the unit and locate the lower sliding portion

of the cool wall assembly. Push this piece toward the back of the unit as
far as it will go to open the cool wall air channel.

4. Remove the strip of insulation.

5. Remove the three screws from the inner cover piece in the

locations shown.

9. Tighten the two outer screws that were loosened to secure the sliding

piece in place.

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands