Regency Grandview G600C Owners & Installation Manual Download Page 55

Page: 55 / 104

installation

Grandview

G600C Gas Fireplace

Venting Arrangements with Co-linear Flex System into a Masonry Chimney Application

THE APPLIANCE MUST NOT BE

CONNECTED TO A CHIMNEY FLUE

SERVING A SEPARATE SOLID FUEL

BURNING APPLIANCE.

This appliance is designed to be attached to
two 3" (76mm) co-linear aluminium flex running
the full length of the chimney. See the Venting
Arrangements on next page for minimum and
maximum heights.

Masonry chimneys may take various contours which the flexible liner will accommodate. However,

keep

the flexible liner as straight as possible

, avoid unnecessary bending.

The Air Intake pipe must be attached to the inlet air collar of the termination cap.

Required Parts:

Part #

Description

946-529

Co-linear DV Vertical

Termination Cap

948-305

3" Flex - 35 ft.

946-563

Co-Axial to Co-Linear Adapter Kit

which contains the following:

Co-linear Flex Adapter

Outer Pipe

Inner Pipe Adapter

510-994

Rigid Pipe Adapter

Alternate Approved Caps

46dva-VC Vertical Termination Cap
46dva-VCH High Wind Cap
46dva-GK 3" Co-linear Adapter with flashing

Flex Liner

Exhaust

Flue

A maximum

of two certiﬁed

joiner kits

may be used

per length.

#948-305 (35 ft)

Air Intake

Co-linear DV

Vertical Termination

Cap # 946-529

Co-Linear

Flex

Adapter

with Kit#

946-563

Outer

Pipe

with Kit#

946-563

Inner Pipe

Adapter

with Kit#

946-563

Rigid Pipe Adapter

# 510-994

90 Degree

Elbow

Pipe Length

NOTE:

See detailed venting arrangements, vertical

terminations, co-linear flex system into ma-
sonry fireplaces in this manual.

IMPORTANT: As shown below, the unit can only be vented from the top, not from the rear.

Top exit only.
Cannot be vented from the
rear.

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands