Regency Grandview G600C Owners & Installation Manual Download Page 5

Page: 5 / 104

Grandview

G600C Gas Fireplace

table of contents

Owner's Information

Copy of Safety Decal .............................................................................6

Unit Dimensions ..................................................................................10

Before You Start ...................................................................................11

Important Message .............................................................................12

General Safety Information ..................................................................12

To Turn Appliance On/Off.....................................................................12

Optional Fan Operation .......................................................................12

Lighting the Pilot Using the Gas Control Knob Extender .....................13

Copy of Lighting Plate Instructions ......................................................14

Operating Procedure for Optional Remote Control (Part # 761-976) ..15

Safety Screen Removal .......................................................................16

Safety Screen Installation ....................................................................16

Glass Door Removal............................................................................16

Glass Door Installation ........................................................................16

Gas Installation Checklist ......................................................................9

Installation Checklist ............................................................................17

Locating Your Gas Fireplace ................................................................17

Heatwave Duct System Optional Kit ...................................................17

Clearance / Framing and Venting Configurations ................................18

Cool Wall Installation (Combustible Finishing) .................................... 19

Non-Combustible Installation .............................................................. 19

Unit Assembly Prior to Installation (Nailing Flange Installation) ......... 20

Nailing Flange Installation .................................................................. 21

Cool Wall Clearances ......................................................................... 23

Cool Wall Mantel Clearances ............................................................. 24

Cool Wall Mantel Leg Clearances ...................................................... 24

Cool Wall Installation—Framing .......................................................... 25

Cool Wall Installation-Cool Wall Conversion ....................................... 26

Chase Venting .................................................................................... 27

Chase Vent Installation - Cool Wall (Part #776-941)........................... 28

Clean Front Installation (Non Cool Wall) - Clearances ....................... 29

Clean Front Installation (Non Cool Wall) - Mantel Clearances ........... 30

Clean Front Installation (Non Cool Wall) - Mantel Leg Clearances .... 31

Clean Front Installation (Non Cool Wall)—Non Combustible

Requirements ................................................................................... 31

Clean Front Installation—Framing (Non Cool Wall) ............................ 32

Clean Front Installation ....................................................................... 33

Outside Finish Installation (Non Cool Wall)—Clearances................... 34

Outside Finish Installation (Non Cool Wall) - Mantel Clearances ....... 35

Outside Finish Installation (Non Cool Wall)—Mantel Leg

Clearances ....................................................................................... 35

Outside Finish Installation (Non Cool Wall)—Framing ........................ 36

Outside Finish—Finishing .................................................................. 37

Faceplate Installation (Part # 776-922, 776-924, 776-926) ................ 38

Finishing Trim Install (Part # 776-928) ................................................ 39

Wall Board/Drywall Installation ........................................................... 41

Conversion to Rear Vent ..................................................................... 42

Vent Restrictor Installation (Part # 776-027) ....................................... 45

Venting Introduction .............................................................................45

Exterior Vent Termination Requirements .............................................46

4" X 6-5/8" (102 mm - 168 mm) Rigid Pipe - Cross Reference

Chart Only .........................................................................................47

Venting Arrangements for Horizontal Terminations - Flex Vent or

Rigid Pipe 4" x 6-5/8" (102 mm x 168 mm) .......................................49

Venting Arrangements - Horizontal Termination - Rigid Pipe and

Direct Vent System (Flex) .................................................................51

Venting Arrangements Vertical Termination - Rigid Pipe System and

Vertical Flex Kit to Same Limitations ...............................................52

Horizontal Terminations - Two 90°Elbows ...........................................53

Horizontal Terminations - Three 90

Elbows .......................................53

Vertical Venting With Two 90

Elbows ..................................................54

Vertical Venting With Three 90

Elbows ............................................54

Venting Arrangements with Co-linear Flex System into a Masonry

Chimney Application ..........................................................................55

Venting Arrangement - Vertical Terminations - Co-linear Flex System

Into Masonry Fireplaces .................................................................56

Unit Installation with Horizontal Termination ........................................57

Unit Installation with Vertical Termination ............................................58

Direct Vent System (Flex) Installation Procedures ...............................59

Vertical Termination 4' x 6-7/8' (102 mm x 175 mm) Venting

- Vertical Flex Vent Kit (Part #946-755) ..............................................60

Vertical Flue Extension Kit (Part #946-756).........................................61

Ceiling Firestop / Firestop Spacer (Part #946-757) .............................61

Conversion from NG to LP for G600C Using SIT 885 PROFLAME

Gas Valve ..........................................................................................62

Conversion from NG to LP for G600C using SIT 825 PROFLAME

Gas Valve ..........................................................................................64

Brick Panel Installation (Part # 776-901, 776-903, 776-904,

776-905) ............................................................................................66

Enamel/Steel Panel installation (Steel Panels - Part # 776-907,

Enamel Panels - Part # 776-908) ......................................................67

Log Set Installation ..............................................................................68

Crystal Tray Installation (Part #776-937) .............................................73

Driftwood Media Tray Installation .........................................................74

Pilot Adjustment ...................................................................................76

High Elevation ......................................................................................76

SIT 820 Valve Description ...................................................................76

G600C - NG System Data ..................................................................76

G600C - LP System Data ...................................................................76

Gas Pipe Pressure Testing ..................................................................76

Aeration Adjustment ............................................................................77

Electrical Access and Installation ........................................................77

Optional Wall Thermostat (Part #910-407) .........................................78

Optional Remote Control (Part # 761-976) ..........................................78

Optional Wall Switch (Not Supplied by Regency) ................................78

Installing an Optional Wall Switch (Not Offered by Regency) or

Thermostat (Part # 910-407 or 910-404/P) .......................................79

Wiring Diagram With and Without Thermostat/Remote Control ..........80

Installing the Optional Fan (Part 761-979) ..........................................81

Fan Install After Unit Installation ..........................................................82

Fan Wall Control Installation Kit (Part # 761-974) ................................83

Optional On/Off Remote Kit Installation (Part # 761-976) ...................85

Safety Screen Removal .......................................................................86

Safety Screen Installation ....................................................................86

Glass Door Removal............................................................................86

Glass Door Installation ........................................................................86

Operating Instructions .........................................................................87

First Fire ..............................................................................................87

Normal Operating Sounds of Gas Appliances .....................................87

Receiver Battery Replacement ...........................................................88

DC Spark Igniter Battery Installation/Replacement .............................88

Copy of Lighting Plate Instructions ......................................................89

Maintenance Instructions.....................................................................90

General Vent Maintenance ..................................................................90

Log Replacement ................................................................................90

Glass Gasket .......................................................................................90

Door Glass ...........................................................................................90

Glass Replacement .............................................................................90

Valve Replacement ..............................................................................91

Gas Appliance Maintenance ................................................................92

Main Assembly ....................................................................................93

Parts ....................................................................................................94

Optional Accessories ...........................................................................95

Warranty .............................................................................................96

Installer's Information

Installation

Maintenance

Operation

Parts

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands