Regency Grandview G600C Owners & Installation Manual Download Page 68

Page: 68 / 104

Grandview

G600C Gas Fireplace

installation

Log Set Installation

09.16.20

920-294

LOG SET INSTALLATION

Page 1 of 4

Rear Log

Middle Left Log

Middle Right Log

Center Left Cross Log

Front Bottom 'Y' Log

Left Rear Log

Right Cross Log

Middle Front

Left Log Piece

Right Log Piece

Left Front Log Piece

Right Front Log Piece

Must also purchase (#776-938),
Log Grate and Ember Package,
separately. The kit contains:

Log Grate

3/4" Ginger glass

Vermiculite

Black/White Embers

Log Support Plates

Read the instructions below carefully and refer to the diagrams.
If logs are broken do not use the unit until they are replaced.
Broken logs can interfere with the pilot operation.

The G600EC/G600C/G600C-1 log sets, #776-930 for Grandview Oak,
#776-932 for Grandview Birch, contain the following pieces:

NOTE: Panels (brick, steel, or enamel) must be installed

prior to installing the log set.

1. Carefully remove the logs from the box and unwrap them. The logs

are fragile, handle with care -

do not force into position when

installing.

2. Install the log grate—secure with 2 screws in locations shown below.

3. Install the supplied crystals over the ember lights underneath the

burner as shown. Place vermiculite and embers on top of the glass.
Do not place any media on the burner.

Diagram 1-Log ID

Diagram 2-Log Grate Install

Diagram 3-Install Glass

Diagram 4-Install Vermi Lava

Warning: Glass crystals must be placed at least 1" away from the

front edge of the unit.

G600EC/G600C/G600C-1

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands