background image

 1 

 

 

 

 

                        7036-188J 

 

 

 

       October 3, 2017

MT VERNON PELLET INSERT

ADVANCED ENERGY (AE)

Model(s):

MTVERNINSAE-MBK

MTVERNINSAE-PMH

MTVERNINSAE-CSB

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation. 

OWNER: Retain this manual for future reference. 

NOTICE: DO NOT DISCARD THIS MANUAL

 

HOT SURFACES! 

 

Glass and other surfaces are hot  

 

during operation AND cool down.  

Hot glass will cause burns.

• 

Do not touch glass until it is cooled

• 

NEVER allow children to touch glass

• 

Keep children away

• 

CAREFULLY SUPERVISE children in same room as 

fireplace.

• 

Alert children and adults to hazards of high temperatures

•  High temperatures may ignite clothing or other 

flammable materials.

• 

Keep  clothing,  furniture,  draperies  and  other  flammable 

materials away.

 WARNING

If the information in these instruc-

tions is not followed exactly, a 

fire may result causing property 

damage, personal injury, or death.

 

•  Do not store or use gasoline or other flam

-

mable vapors and liquids in the vicinity of 

this or any other appliance.

•  Do not over fire - If appliance or chimney 

connector glows, you are over firing. Over 

firing will void your warranty.

•  Comply with all minimum clearances to 

combustibles as specified.  Failure to 

comply may cause house fire.

WARNING

CAUTION

Tested and approved for wood pellets, shelled field 

corn, wheat and black oil sunflower seeds. Burning of 

any other type of fuel voids your warranty.

NOTE

To obtain a French translation of this manual, please contact 

your dealer or visit www.quadrafire.com

Pour obtenir une traduction française de ce manuel, s’il vous 

plaît contacter votre revendeur ou visitez www.quadrafire.com

CAUTION

Check building codes prior to installation.

•  Installation MUST comply with local, regional, state and na-

tional codes and regulations.

•  Consult local building, fire officials or authorities having juris

-

diction about restrictions, installation inspection, and permits.

Installation and service of this appliance should be performed by 

qualified personnel. Hearth & Home Technologies recommends 

HHT Factory Trained or NFI certified professionals.

Summary of Contents for MTVERNINSAE-CSB

























Reviews: