Regency Grandview G600C Owners & Installation Manual Download Page 73

Page: 73 / 104

installation

Grandview

G600C Gas Fireplace

Crystal Tray Installation (Part #776-937)

09.30.20

920-295

CRYSTAL TRAY INSTALLATION

Page 1

Part #776-937

G600EC/G600C

2. Attach the crystal tray with two screws, one on the middle

left and another on the middle right of the tray, as shown
below.

3. Add 5 lbs of crystal media and spread it across the tray in

one even layer.

Important: ensure that at least 50% of the

gas burner porting remains uncovered. Do not cover
the pilot area.

BURNER PORTING

PILOT

4. If using volcanic stones as additional media, add a maximum

of 10, as shown below.

Important: Volcanic stones should

not cover any of the gas burner porting or pilot areas.

Note: The optional brick, steel, or enamel panels must be

installed prior to the crystal tray.

1. Place the crystal tray over the burner, as shown below.

5. To remove the crystal tray, reverse the steps above.

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands