Regency Grandview G600C Owners & Installation Manual Download Page 67

Page: 67 / 104

installation

Grandview

G600C Gas Fireplace

Enamel/Steel Panel installation (Steel Panels - Part # 776-907, Enamel Panels - Part # 776-908)

08.04.20

920-296

ENAMEL/STEEL PANEL INSTALLATION

5. Loosen screws and remove brick clips.

1. Remove screen and glass door, if installed.

2. Loosen two screws in locations shown below. Slide upper baffle

towards the back wall and then remove from unit.

6. Install the right side panel—the angled face should be located facing

the bottom rear of the fireplace when installing.

7. With panel in position, secure it with the brick clip removed in Step

5 and tighten the screw.

For Black Enamel Panels:

• Black enamel panels must be inspected for scratches and dimples

prior to installation. All claims are to be recorded at this time.

Claims for damage after installation will not receive consideration.

• Black enamel panels will discolor a little during normal operation.

This is normal and should not be considered a defect.

* All hand and fingerprints MUST be cleaned off with a soft cloth.

Use an ammonia-based cleaner (ie. glass cleaner) to remove any
fingerprints before applying heat to the unit.

Failure to do this will result in burn stains on panels which you

will be unable to remove. Not protected by product warranty.

G600EC/G600C

3. Loosen 2 screws on pilot assembly in locations shown below.

Slide pilot shield towards the back of the unit and remove from
unit.

8. Repeat Steps 5-7 on the left side.

4. Install back panel carefully. Tilt panel forward from the top and rest

the bottom of the panel on the firebox floor. Tip top back until it also
rests on the firebox back wall.

10. Reinstall the upper baffle.

11. Reinstall the pilot shield removed in step 3.

9. Slide the bottom panel carefully underneath the burner and

push to the back until it contacts the back panel.

Note: Do not install the firebed grate, media, vermiculite, embers,

and logs until the enamel/steel panels are installed.

PART # 776-907, 776-908

Item Part #

Description

N/A

Inside Top of Firebox

N/A

Panel

761-049 Brick Clip

904-519 Screw

tooltip

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands