Regency Grandview G600C Owners & Installation Manual Download Page 27

Page: 27 / 104

installation

Grandview

G600C Gas Fireplace

Chase Venting

Note: The enclosure opening cannot be any lower than 0-2" (0-51mm) from the top of the enclosure for all installations. Minimum height of
enclosure from base of appliance is 74-1/2" (1892mm).

A minimum 58in

opening in the enclosure is required to maintain safe opeating temperatures. This can be achieved in a number of ways

including the examples shown below.

Warning: DO NOT cover or place objects in front of the air outlets.

CHASE VENTING

A minimum

opening in the enclosure is required to maintain safe operating

temperatures. This can be achieved in a number of ways including the examples shown below.

Warning: DO NOT cover or place objects in front of the air outlet(s).

Regency Chase Vent

Custom chase vent

Reveal at the chase top

Regency Chase Vent

Custom Chase Vent

Reveal at the Chase Top

Summary of Contents for Grandview G600C









































































































Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands

Regency Grandview G600C, Owners & Installation Manual

Search results

Summary of Contents for Grandview G600C

Reviews:

Related manuals for Grandview G600C

Brands by name

Popular brands