Empire Comfort Systems Tahoe DVP36PP32EN-1 Installation Instructions And Owner'S Manual Download

Page: 1 / 64

DIRECT VENT

GAS FIREPLACE HEATER

MODEL SERIES

DVP36PP32EN-1

DVP36PP32EP-1

DVP36SP32EN-1

DVP36SP32EP-1

UL FILE NO. MH30033

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

WARNING: If not installed, operated and maintained

in accordance with the manufacturer’s instructions,

this product could expose you to substances in fuel or

from fuel combustion which can cause death or seri-

ous illness.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA only)

or mobile home, where not prohibited by state or local

codes.
This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certiﬁed

kit is used.

The Tahoe Direct Vent Zero Clearance Gas

Fireplace Heater

GAS-FIRED

Installer: Leave this manual with the appliance.

Consumer: Retain this manual for future reference.

— Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

ﬁre department.

— Installation and service must be performed by a

qualiﬁed installer, service agency or the gas sup-

plier.

WARNING: If the information in these instructions

are not followed exactly, a ﬁre or explosion may re-

sult causing property damage, personal injury or

loss of life.

Page 1

Summary of Contents for Tahoe DVP36PP32EN-1

































































Search results

Summary of Contents for Tahoe DVP36PP32EN-1

Reviews:

Related manuals for Tahoe DVP36PP32EN-1

Brands by name

Popular brands

Empire Comfort Systems Tahoe DVP36PP32EN-1, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for Tahoe DVP36PP32EN-1

Reviews:

Related manuals for Tahoe DVP36PP32EN-1

Brands by name

Popular brands