Empire Comfort Systems Tahoe DVP36PP32EN-1 Installation Instructions And Owner'S Manual Download Page 57

Page: 57 / 64

24325-0-0708

Page 57

ACCENT LAMP

12 VOLT SIDE

120 VOLT SIDE

TRANSFORMER

(R9344)

CORDSET

(R6159)

RHEOSTAT ASSEMBLY

(18879)

Your Direct Vent Gas Fireplace comes equipped with an "Accent

Lamp." The light has been pre-wired and is controlled from the

Rheostat.

If in the event the lamp or lens needs to be replaced, follow the

instructions below:

1. Unplug the Accent Lamp/transformer from the junction box

inside the ﬁreplace.

2. Remove the four screws that secure the lens frame. This frame

retains the glass lens. The bulb can now be accessed.

Note:

Do not handle the lamp (bulb) with bare ﬁngers, protect

with clean dry cloth.

The lamp will pull straight out of the socket. Replace with 10

Watt/12 Volt Halogen bulb.

When re-installing, ensure integrity of gasket seal.

THE FIREBOX MUST BE SEALED.

Over-tightening the screws could break the lens.

"Light Leakage" from the upper area may be observed. The holes

in the lamp housing are necessary for ventilation and must not be

covered.

Figure 68 - Accent Lamp Wiring

COVER

LAMP

GLASS

GASKET

BEZEL

Figure 69 - Accent Lamp Parts

Part Number

Description

23116

Cover

R9340

Lamp

R9658

Gasket

R9341

Glass

R9342

Bezel

Summary of Contents for Tahoe DVP36PP32EN-1

































































Search results

Summary of Contents for Tahoe DVP36PP32EN-1

Reviews:

Related manuals for Tahoe DVP36PP32EN-1

Brands by name

Popular brands

Empire Comfort Systems Tahoe DVP36PP32EN-1, Installation Instructions And Owner'S Manual

Search results

Summary of Contents for Tahoe DVP36PP32EN-1

Reviews:

Related manuals for Tahoe DVP36PP32EN-1

Brands by name

Popular brands