Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download Page 33

Page: 33 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

10000001052

The set heading value is adjusted via the rotary knob and activated either by the

SET button or by pressing down the rotary knob.

A direct heading change can be performed by pressing down and turning the

rotary knob; in this mode the ship follows the new value (see Figure 5).

Please note:

The direction (turn direction) of a heading change depends on the turn direction of

the rotary knob.

For step by step instructions for Heading Control/heading change, see section 4.

After switching over from manual steering to steering control via the Autopilot, the

actual heading will be taken as the set heading on the Autopilot.

Summary of Contents for NautoPilot 5000 Series
































































































































































































Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands

Raytheon Anschütz NautoPilot 5000 Series, Operator'S Manual

Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands