Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download Page 154

Page: 154 / 191

NautoPilot® 5000 Series
102-890.NG001-NG003
Operator Manual

10000001052

138

Edition: 003

5.4 Operation

With the Additional Autopilot Control Unit, it is possible to control the NautoPilot®

in the modes:

- Heading Control

- and Course Control.

NOTE:

No Track Control able.

The Track Control mode is started by a track planning system (ECDIS, Raytheon
Anschütz). See chapter 4.5.1

5.4.1

Heading Control

Procedure:

1. Select the softkey ACTIVE in the section PANEL.

2. The softkey is highlighted and the indicator lamp lights green.

3. Select the softkey HEADING CONTROL in the Section PANEL.

4. The softkey is highlighted and the STEERING MODE displays Heading Ctrl. or if the

panel is not active and Manual Control is active, you can also press Heading Control
directly.

Step result:

5. Set the desired heading and radius by using the joystick.

5.4.2

Course Control

Summary of Contents for NautoPilot 5000 Series
































































































































































































Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands

Raytheon Anschütz NautoPilot 5000 Series, Operator'S Manual

Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands