Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download Page 158

Page: 158 / 191

NautoPilot® 5000 Series
102-890.NG001-NG003
Operator Manual

10000001052

142

Edition: 003

5.8 Switching between night and day display (dimming) Change Display

Colors

The display can be configured for different conditions by changing the color

combinations.

Following color modes are available:

- Bright Sun Colors

Bright on white background

- Day Colors - White

Dark on white background

- Day Colors - Black

Bright on black background

- Dusk Colors

Fluorescent on black background

- Night Colors

Fluorescent dim on black background

Procedure:

1. Select

Menu

from the top right corner of the display:

- The submenu opens.

2. Select Color Palettes.

- The drop- down menu opens.

3. Select the desired color mode.

- The color combination on the screen changes.

Summary of Contents for NautoPilot 5000 Series
































































































































































































Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands

Raytheon Anschütz NautoPilot 5000 Series, Operator'S Manual

Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands