Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download Page 134

Page: 134 / 191

NautoPilot® 5000 Series
102-890.NG001-NG003
Operator Manual

10000001052

118

Edition: 003

4.4.6

Course change in Course Control mode

There are 2 ways to change a Course Over Ground (COG) value:

- Changing preselected COG value with rotary knob and SET button

- Direct COG change

Preselected

Changing the value with the rotary knob and acknowledging the value

with the SET button or with the rotary knob has the same result - but

the procedure is a little different.

This procedure can be used, if a COG change is in preparation.

Direct COG change

This procedure is similar to the direct heading change in Heading Control mode, but

the new COG value is active after releasing the rotary knob, there is no continuous

COG change.

This procedure is displayed also as Preselected COG.

After a course change is indicated in Course Control
a new course change can be ordered until the

Course Approach” alert is not indicated.
Please note: each time the heading is changed in this

way, the ”Distance to Course line” is set to zero and
must be calculated anew.

Summary of Contents for NautoPilot 5000 Series
































































































































































































Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands

Raytheon Anschütz NautoPilot 5000 Series, Operator'S Manual

Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands