Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download

Page: 149 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

133

10000001052

5.2.3

Autopilot Values

Table 37

Description of the Quality Indicators according to IEC 62288

No. Area / Element

Description

SET HEADING /
SET COURSE

Displays the set heading or course that was set via
the NautoPilot® or the Additional Autopilot Control.

SET RADIUS / SET
RATE

Displays the set turn radius in NM or the set Rate
of Turn in degrees that was set via the NautoPilot®
or the Additional Autopilot Control Unit.

USED SPEED

Displays the used speed and the sensors that supply
the data:
WT = Water Track (Log)
BT = Bottom Track (GPS / Doppler Log)

RUDDER LIMIT

Displays the set Rudder limit.

Colored
Quality
Indicator

See: Description of the Quality Indicators ac-
cording to IEC 62288 (Table 34).

5.2.4

Menu

Table 38

Menu Bar Content

Designation

Function

Color Palettes

Change color mode.

Dimming

Change dimming adjustment.

Setting

Change system and profile configuration.

Exit

Exit this application.

Figure 60: Autopilot Values

Summary of Contents for NautoPilot 5000 Series
































































































































































































Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands

Raytheon Anschütz NautoPilot 5000 Series, Operator'S Manual

Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands