Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download Page 127

Page: 127 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

111

10000001052

Heading Control mode is active.
The mode is displayed at the top right corner of the display
(Heading Ctrl.).

Preselected Heading

125.8

Turning the rotary knob will change the preselected heading
value.

Please note: After approx. 15 seconds of inactivity from
rotary knob, the primary heading value is displayed again.

This value is displayed in italic and colors are inverted.

The SET LED (near the button) will flash (request to press
the SET button).

Set Heading

125.8

Pressing the rotary knob transmits the preselected value to
the controller as the new set heading (this procedure is
similar to that for a Direct heading change).

The value is now displayed in non- italics and normal colors.

The SET LED (near the button) will be off.

Please note:

- It is necessary to observe the Autopilot control function after a heading change.

Summary of Contents for NautoPilot 5000 Series
































































































































































































Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands

Raytheon Anschütz NautoPilot 5000 Series, Operator'S Manual

Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands