Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download Page 141

Page: 141 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

125

10000001052

- The NautoPilot® version is NP 5100 or NP 5300 (for NautoPilot® with a higher

performance e.g. for type NP 5400 and NP 5500 it is not possible

to connect to GPS, chart plotter or equivalent navigation

system).

- Heading value is valid and not obtained from a Magnetic Compass.

- Speed value is valid.

- Track Limit Autopilot is configured.

- The serial interface which is connected to the navigational system is configured to

NMEA 4800 Bd or NMEA 38400 Bd (see also Installation Manual).

- The navigational system has already transmitted an APB NMEA telegram

(according to IEC 61162- 1) (this includes Track Course and a Cross Track error).

- The actual cross track error is not more than 1 nautical mile.

- The difference between the actual heading and the track heading is less than 60



- The NautoPilot® is in Heading Control Mode.

After the navigational system has transmitted the APB telegram, the Track button

at the NautoPilot® Operator Unit must be pressed to activate waypoint steering

mode.

Waypoint steering mode is inactive.
Press Track button.

Waypoint steering mode is active.
The mode is displayed at the top right corner of the display.

Summary of Contents for NautoPilot 5000 Series
































































































































































































Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands

Raytheon Anschütz NautoPilot 5000 Series, Operator'S Manual

Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands