Raytheon Anschütz NautoPilot 5000 Series Operator'S Manual Download Page 27

Page: 27 / 191

NautoPilot® 5000 Series

102-890.NG001-NG003

Operator Manual

Edition: 003

10000001052

magnetic compass.

The monitoring threshold is set via the Page function

(Page

→

Limit

→

Heading Monitor) at the initial display. It allows settings from 5



in increments of 1



The difference between Gyro heading and magnetic heading exceeds the preset

threshold, an alert is generated.

During a heading change maneuver this function is automatically paused, due to

the inert behavior of the Magnetic compass.

For switching on or off the Heading Monitor refer to Installation Manual, chapter

on Heading Monitor.

1.3.6

OFF Heading

This function compares the actual heading value against the set heading value.

There is an alarm if the limit between set heading and actual heading exceeds a pre-

adjusted value (Page

→

Limit

→

OFF Heading). See also section 2.3.6.4.

The possible range for pre- adjusted OFF Heading value 5



to 30



(in increments of



). The alarm is suppressed for a calculated time after a heading change

maneuver (calculation is based on RAD or RoT

→

time window).

The time window is calculated from the difference in the desired heading and

the preselected turning rate.

If, during the heading change maneuver, the ship reaches the heading alarm

threshold within the time window, no alarm is triggered.

Summary of Contents for NautoPilot 5000 Series
































































































































































































Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands

Raytheon Anschütz NautoPilot 5000 Series, Operator'S Manual

Search results

Summary of Contents for NautoPilot 5000 Series

Reviews:

Related manuals for NautoPilot 5000 Series

Brands by name

Popular brands