Pro-face GP3000 Series Maintenance & Troubleshooting Download Page 42

Page: 42 / 164

Problems with PC operation

Maintenance/Troubleshooting

1-42

(3) After the [System Properties] window opens, click the [Hardware] tab and select [Device

Manager].

(4) After the [Device Manager] window opens, click the [+] mark to the left of [USB (Universal

Serial Bus) Controller]. If you find [USB Link Cable (CA3-USBCB-01)] in the displayed list,

the driver has been installed successfully.

• Driver installation procedure

If the driver has not been installed, re-install it according to the procedure below.

Connect the PC and the Display through the USB transfer cable optionally available

from Pro-face.

• If the

mark is displayed to the left of [USB Link Cable (CA3-USBCB-01)],

disconnect the USB cable from the PC and then re-connect it. After that, perform
the installation procedure. For the installation procedure, see the next page.

Summary of Contents for GP3000 Series





































































































































































Search results

Summary of Contents for GP3000 Series

Reviews:

Related manuals for GP3000 Series

Brands by name

Popular brands

Pro-face GP3000 Series, Maintenance & Troubleshooting

Search results

Summary of Contents for GP3000 Series

Reviews:

Related manuals for GP3000 Series

Brands by name

Popular brands