Planet IP DSLAM IDL-2400 User Manual Download Page 463

Page: 463 / 707

IP DSLAM

463

Output:

Verbose Mode On

Entry Created

VLAN Index : 6 Port Index : 6

Querier Port Status : Mgmt

Verbose Mode Off:

Entry Created

Output field:

Field

Description

VLAN Index

VlanId to uniquely identify the vlanid of the entry

for which the IgmpSnooping Querier is

configured/ learned. In devices supporting

"Shared Vlan for multicast" capability, the

information for a Querier port is shared across

vlans. Hence vlan id is an optional parameter. In

devices supporting "Independent Vlan for

multicast" capability, each vlan can have its own

information for a Querier port. Hence vlanid is a

mandatory parameter in all the commands other

than - get. For No Vlan case, vlan id is not

required. This Feature is not supported for VLAN

with vlanid as 4097.

Port Index

A Bridge Port, belonging to the Vlan

(dot1qVlanIndex), on which the Querier exists.

Querier Port Status

Specifies whether Querier Port has been learned

dynamically or configured by the user.

Caution:

An entry in this table shall not be applicable for a bridge port created over the

PPPoE interface.

Summary of Contents for IP DSLAM IDL-2400




































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IP DSLAM IDL-2400

Reviews:

Related manuals for IP DSLAM IDL-2400

Brands by name

Popular brands

Planet IP DSLAM IDL-2400, User Manual

Search results

Summary of Contents for IP DSLAM IDL-2400

Reviews:

Related manuals for IP DSLAM IDL-2400

Brands by name

Popular brands