Planet IP DSLAM IDL-2400 User Manual Download Page 385

Page: 385 / 707

IP DSLAM

385

Optional

Modify

－

Optional

Default value:

"\0"

priority <

priority-val>

Priority to be set for packets matching this rule. This field is valid

only if RuleAction is 'setprio' or 'retagprio'. If the RuleAction is

'setprio' then this value is internal priroity and is used along with

egress port traffic class mapping table, to determine the output

queue. If the RuleAction is 'retagprio' then this value is priority which

is to be tagged into the outgoing packet and it is also used along with

egress port traffic class mapping table, to determine the output

queue. This field can be modified only if 'status' has the value

'disable'.

Type:

Create

－

Optional

Modify

－

Optional

Valid values:

0 - 7

Default value:

status

enable | disable

Admin status of the rule

Type:

Create

－

Optional

Modify

－

Optional

Default value:

disable

statsstatus

enable

|disable

Admin status of rule statistics. Statitics of a rule are collected only

when this field is set to 'enable'. This field can be modified only if

'status' has the value 'disable'. NOTE - Statistics may not reflect

correctly the number of egress mcast, bcast and unknown unicast

packets hitting the rule.

Type:

Create

－

Optional

Modify

－

Optional

Default value:

disable

ruleprio

low | high

Tells the priority of the rule. Based on this priority value, the rule is

created in fast or slow memory. This field can be modified only if

'status' has the value 'disable'. This field is ignored if the 'ruleAction'

has value 'clfrdef'

Type:

Create

－

Optional

Modify

－

Optional

Default value:

high

ruledir

in | out

Specifies whether the rule will be applied on incoming interfaces

(ingress)or outgoing interfaces(egress).

Type:

Create

－

Optional

Default value:

Summary of Contents for IP DSLAM IDL-2400




































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IP DSLAM IDL-2400

Reviews:

Related manuals for IP DSLAM IDL-2400

Brands by name

Popular brands

Planet IP DSLAM IDL-2400, User Manual

Search results

Summary of Contents for IP DSLAM IDL-2400

Reviews:

Related manuals for IP DSLAM IDL-2400

Brands by name

Popular brands