manualshive.com logo in svg

Planet IP DSLAM IDL-2400, User Manual

The Planet IP DSLAM IDL-2400 product is an advanced DSL access solution. To ensure smooth setup and configuration, we offer a comprehensive User Manual for free download on our website. Equipped with all the necessary instructions and troubleshooting guidelines, it's your go-to resource for maximizing the potential of this outstanding product. Download it today from manualshive.com.

Share
Download
background image

IDL series User Guide

 

620 

Type:

 Modify 

－

 Optional  

Valid values: 

1 -8   

maxmulticast 

<

maxmulticast-val>   

Maximum number of multicast groups that can be 

configured in the system   

Type:

 Modify 

－

 Optional  

Valid values: 

1 - 4   

maxmac <

maxmac-val>   

Maximum number of MAC addresses that can be learned by 

the system. This should be a multiple of 32   

Type:

 Modify 

－

 Optional  

Valid values: 

1 - 4000 

maxhashbuck 

<

maxhashbuck-val>   

Maximum number of hash buckets for the Forwarding table. 

This value should be a power of 2. (1, 2, 4, 8 ,...)   

Type:

 Modify 

－

 Optional  

Valid values: 

1 - 8192   

maxnumvlan 

<

maxnumvlan-val>   

Maximum number of VLANs that can be configured on the 

Bridge either statically or dynamically   

Type:

 Modify 

－

 Optional  

Valid values: 

0 - 512   

maxvlanidval 

<

maxvlanidval-val>   

Maximum value of VLAN ID that this Bridge can support   

Type:

 Modify 

－

 Optional  

Valid values: 

1 - 4095 

maxnumacentry 

<

maxnumacentry-val>   

Maximum number of Static UCast Entries that can be 

configured on the Bridge   

Type:

 Modify 

－

 Optional  

Valid values: 

0 - 512   

devcap IVL | SVL | none

   

Device Capabilities of Q-Bridge MIB. In case of Stacked 

Vlan Mode this shall apply to Virtual Vlans. 

Type:

 Modify 

－

 

Optional  

bridgingmode Restricted 

|Unrestricted | 

Residential 

 

This specifies the state of full bridging on the bridge. Value 

residential species that packets coming from CPE side 

would be forwarded to the net side port without a lookup. In 

case of restricted bridging, the packets would undergo a 

lookup and if the destination is another CPE port, the packet 

would be dropped, i.e. CPE to CPE traffic is not allowed. 

Unrestricted bridging is forwarding based on lookup in all 

cases.  

Type:

 Modify 

－

 Optional  

maxhpriotreenodes 

<

maxhpriotreenodes-val>   

Maximum number of classifier tree nodes of high access 

priority that can be created. 

Type:

 Modify 

－

 Optional  

Summary of Contents for IP DSLAM IDL-2400




































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IP DSLAM IDL-2400

Canon 70 MC - ZR70MC MiniDV Digital Camcorder Instruction Manual preview
70 MC - ZR70MC MiniDV Digital Camcorder
Brand: Canon Pages: 57
Novell LINUX ENTERPRISE DESKTOP 11 - KDE Manual preview
LINUX ENTERPRISE DESKTOP 11 - KDE
Brand: Novell Pages: 102
Sony Ericsson Controller Mode Application Note preview
Controller Mode
Brand: Sony Ericsson Pages: 10
ZixCorp PocketScriptTM User Manual preview
PocketScriptTM
Brand: ZixCorp Pages: 44
ACRONIS ADVANCED SERVER Datasheet preview
ADVANCED SERVER
Brand: ACRONIS Pages: 2
Brocade Communications Systems IronWare Release Note preview
IronWare
Brand: Brocade Communications Systems Pages: 40
Brocade Communications Systems Brocade BladeSystem 4/24 Administrator'S Manual preview
Brocade BladeSystem 4/24
Brand: Brocade Communications Systems Pages: 62
Brocade Communications Systems Fabric OS v7.0.1 Command Reference Manual preview
Fabric OS v7.0.1
Brand: Brocade Communications Systems Pages: 1132
Red Hat APPLICATION STACK 2.1 RELEASE Release Note preview
APPLICATION STACK 2.1 RELEASE
Brand: Red Hat Pages: 26
YASKAWA XTRAWARE - V3.0 Manual preview
XTRAWARE - V3.0
Brand: YASKAWA Pages: 263
Adaptec Disk Array Administrator User Manual preview
Disk Array Administrator
Brand: Adaptec Pages: 139
F-SECURE MOBILE ANTI-VIRUS FOR SERIES 60 User Manual preview
MOBILE ANTI-VIRUS FOR SERIES 60
Brand: F-SECURE Pages: 90
Autodesk AutoCAD Design Suite 2013 Installation Manual preview
AutoCAD Design Suite 2013
Brand: Autodesk Pages: 138
FieldServer FS-8700-40 Driver Manual preview
FS-8700-40
Brand: FieldServer Pages: 34
FieldServer FS-8700-54 Driver Manual preview
FS-8700-54
Brand: FieldServer Pages: 8
FieldServer FS-8700-47 Driver Manual preview
FS-8700-47
Brand: FieldServer Pages: 51
Darim VideoSpider User Manual preview
VideoSpider
Brand: Darim Pages: 8
Macrovision Corporation SAMREPORT-LITE 2006 Manual preview
SAMREPORT-LITE 2006
Brand: Macrovision Corporation Pages: 36

Brands by name

Popular brands

Load more brands