Planet IP DSLAM IDL-2400 User Manual Download Page 84

Page: 84 / 707

IDL series User Guide

GsDnBinUsage : 0xFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF

ParametricTestInputFile : -

Data Boost : Enable Upstream PSD : Standard

Conf PM Mode :

Conf PML0 Time(sec) : 180

Conf PML2 Time(sec) : 60 Conf PML2 ATPR (dB/10) : 30

Conf PML2 Min Rate(bps) : 0xfa000

MSG Min Ds : 4000 Minimum Snr Margin(dB/10) : 0

FrontEnd H/W Design : El1508

H/W Pwr Reduction : Disable

GsUsBitSwap : Enable Minimum INP : InpAuto

PML2 Entry Thresh Rate : 0x3e800 PML2 Exit Thresh Rate : 0x7d000

PML2 Entry Rate Min Time : 1800

ADSL ATUR Configuration :

---------------------------

Target Snr Margin(dB/10) : 60 Dnshift SnrMargin(dB/10) : 30

Upshift SnrMargin(dB/10) : 90 Min Upshift Time(sec) : 30

Min Dnshift Time(sec) : 30 Fast Min Tx Rate(bps) : 0x7d00

Intl Min Tx Rate(bps) : 0x7d00 Fast Max Tx Rate(bps) : 0x109a00

Intl Max Tx Rate(bps) : 0x109a00 Max Intl Delay(ms) : 16

MSG Min Us : 4000 Minimum Snr Margin(dB/10) : 310

Maximum Snr Margin(dB/10) : 310

________________________________________________________________________

Set Done

IfName : dsl-0

ADSL ATUC Configuration :

---------------------------

Rate Adaptation : adaptAtStartup

Target Snr Margin(dB/10) : 60 Max Snr Margin(dB/10) : 310

GsRsIntCorrectionUp : 125us Dnshift SnrMargin(dB/10) : 0

Upshift SnrMargin(dB/10) : 120 Min Upshift Time(sec) : 0

Min Dnshift Time(sec) : 0 Fast Min Tx Rate(bps) : 0x7d00

Intl Min Tx Rate(bps) : 0x7d00 Fast Max Tx Rate(bps) : 0x1f38300

Intl Max Tx Rate(bps) : 0x177000 Max Intl Delay(ms) : 1

GsTxStartBin : 0x6 GsTxEndBin : 0x1ff

GsRxStartBin : 0x6 GsRxEndBin : 0x1f

GsMaxBitsPerBin : 15 GsMaxDCo : 256

GsRxBinAdjust : Disable GsEraseProfiles : Disable

Summary of Contents for IP DSLAM IDL-2400




































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IP DSLAM IDL-2400

Reviews:

Related manuals for IP DSLAM IDL-2400

Brands by name

Popular brands

Planet IP DSLAM IDL-2400, User Manual

Search results

Summary of Contents for IP DSLAM IDL-2400

Reviews:

Related manuals for IP DSLAM IDL-2400

Brands by name

Popular brands