Planet IP DSLAM IDL-2400 User Manual Download Page 509

Page: 509 / 707

IP DSLAM

509

Parameters:

Name

Description

ifname

interface-name>

The PPPR interface.

Type:

Create

－

Mandatory

Delete

－

Mandatory

Modify

－

Mandatory

Get

－

Optional

Valid values:

－

254

lowif <

lowif-val>

This specifies the name of the lower AAL5

interface.

Type:

Create

－

Mandatory

Valid values:

0 - 574

maxpdu <

maxpdu-val> This specifies the maximum PDU size on a PPPR

interface.

Type:

Create

－

Optional

Valid values:

0 - 1492

Default value:

1492

ppprackto

ppprackto-val>

Time in seconds to wait for LCP terminate Ack,

after sending a terminate request.

Type:

Create

－

Optional

Modify

－

Optional

Valid values:

0 -10

Default value:

lowiftoggletimerto

lowiftoggletimerto-val>

Time in seconds to wait for lowif to come up

without tearing down the pppr session.

Type:

Create

－

Optional

Modify

－

Optional

Valid values:

0 – 10

Default value:

nature dynamic |

static

Specifies if the interface is dynamic or static in

nature.

Type:

Create

－

Optional

Modify

－

Optional

Default value:

Dynamic

configstatus Normal

|Config

This mode describes the configuration status for

the interface. If the "config" bit is set, this interface

shall be created, but will have a dormant status.

Only after the receipt of an pppoa packet from the

CPE side, this interface shall become active.

Type:

Create

－

Optional

Summary of Contents for IP DSLAM IDL-2400




































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IP DSLAM IDL-2400

Reviews:

Related manuals for IP DSLAM IDL-2400

Brands by name

Popular brands

Planet IP DSLAM IDL-2400, User Manual

Search results

Summary of Contents for IP DSLAM IDL-2400

Reviews:

Related manuals for IP DSLAM IDL-2400

Brands by name

Popular brands