Planet IP DSLAM IDL-2400 User Manual Download

Page: 228 / 707

IDL series User Guide

228

Init Fail Trap

Enables and disables the InitFailureTrap. This object is defaulted

disable.

OpStateTrapEnable

Enables/disables the OpStateChangeTrap

PowerMgmtTrapEnable

This indicates change in power mangement state

Thresh 15Min Lofs(sec)

The number of Loss of Frame Seconds encountered by an ADSL

interface within any given 15 minutes performance data collection

period, which causes the SNMP agent to send an

'adslAturPerfLofsThreshTrap'

Thresh 15Min Loss(sec)

The number of Loss of Signal Seconds encountered by an ADSL

interface within any given 15 minutes performance data collection

period, which causes the SNMP agent to send an

'adslAturPerfLossThreshTrap'

Thresh 15Min Lprs(sec)

The number of Loss of Power Seconds encountered by an ADSL

interface within any given 15 minutes performance data collection

period, which causes the SNMP agent to send an

'adslAturPerfLprsThreshTrap'

Thresh 15Min Ess(sec)

The number of Errored Seconds encountered by an ADSL

interface within any given 15 minutes performance data collection

period, which causes the SNMP agent to send an

'adslAturPerfESsThreshTrap'

Thresh Fast Rate Up(bps)

Applies to 'Fast' channels only. Configured change in rate

causing an adslAturRateChangeTrap A trap is produced when:

ChanCurrTxRate > ChanPrevTxRate plus the value of this object.

Thresh Intl Rate Up(bps)

Applies to 'Interleave' channels only. Configured change in rate

causing an adslAturRateChangeTrap A trap is produced when:

ChanCurrTxRate > ChanPrevTxRate plus the value of this object.

Thresh Fast Rate

Down(bps)

Applies to 'Fast' channels only. Configured change in rate

causing an adslAturRateChangeTrap A trap is produced when:

ChanCurrTxRate < ChanPrevTxRate minus the value of this

object.

Thresh Intl Rate

Down(bps)

Applies to 'Interleave' channels only. Configured change in rate

causing an adslAturRateChangeTrap A trap is produced when:

ChanCurrTxRate < ChanPrevTxRate minus the value of this

object.

References:

ADSL

Commands

Summary of Contents for IP DSLAM IDL-2400




































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IP DSLAM IDL-2400

Reviews:

Related manuals for IP DSLAM IDL-2400

Brands by name

Popular brands

Planet IP DSLAM IDL-2400, User Manual

Search results

Summary of Contents for IP DSLAM IDL-2400

Reviews:

Related manuals for IP DSLAM IDL-2400

Brands by name

Popular brands