Panasonic Toughbook CF-73 Series Reference Manual Download Page 138 | Manualshive

Page: 138 / 159

background image

138

Dealing with Problems (Advanced)

[Advanced] and [Boot] menu can not
be registered

Restart the Setup Utility with the Supervisor Password.

Some items in [Security] menu can not
be registered

Restart the Setup Utility with the Supervisor Password.

F9

does not work

Restart the Setup Utility with the Supervisor Password.

Shutting Down

Windows cannot be shut down or
restarted

If a USB device is connected, try removing it.
It may take one or two minutes to shut down.

Standby/Hibernation Function

Unable to enter standby or hibernation
mode

If a USB device is connected to the computer (note: only for some USB
devices), remove the USB device temporarily. If the problem persists, restart
the computer.
It may take one or two minutes to enter the standby or hibernation mode.
The computer may not enter standby mode properly and seems to be frozen in
the case that the computer is communicating via the modem. If this happens,
press the power switch for four seconds or more to forcibly turn your computer
off.
If there is a disc in the CD/DVD drive that has been formatted using B's CLiP,
the computer will not enter standby or hibernation mode. Remove the disc.

Unable to automatically enter standby
or hibernation mode

If a peripheral is connected to the computer, disconnect the device.
If there is a disc in the CD/DVD drive that has been formatted using B's CLiP,
the computer will not enter standby or hibernation mode. Remove the disc.

The computer does not resume

Did you press the power switch and hold it for four seconds or more? If you
press the power switch and hold it for four seconds or more, the power will be
turned off forcibly. In this case, all unsaved data will be lost.
Did you disconnect the AC adaptor or the battery pack while the computer was
in standby mode?
• If the computer's power supply is disconnected while the computer is in

standby mode, the unsaved data will be lost.

• Power is also consumed when the computer is in hibernation mode. Connect

the AC adaptor.

Setup Utility

«
...
136
137
138
139
140
...
»

Summary of Contents for Toughbook CF-73 Series
































































































































































Reviews:

No comments

Related manuals for Toughbook CF-73 Series

Brand: Acer Pages: 4

Aspire Z5600 Series

Brand: Acer Pages: 11

Brand: Acer Pages: 17

Brand: Acer Pages: 7

SST-GD02B Grandia Sereis GD02

Brand: SilverStone Pages: 14

Brand: FabiaTech Pages: 62

Brand: Sun Microsystems Pages: 92

SPARC classic X

Brand: Sun Microsystems Pages: 198

Brand: Lobo Drives Pages: 40

Height Adjustable Standing Desk 4-Leg

Brand: Uplift Desk Pages: 16

Brand: Jupiter Pages: 2

Precision R5400

Brand: Dell Pages: 111

Brand: IEI Technology Pages: 50

Precision 3430 Small Form Factor

Brand: Dell Pages: 6

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

VPCL117FX - Vaio L Series All-in-one Touch Screen

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands