manualshive.com logo in svg

Omron SMARTSLICE - 04-2008, Operation Manual

Share
Download
Omron SMARTSLICE - 04-2008 Operation Manual Download Page 91

72

Reading the Error History with the DeviceNet Configurator

Section 6-3

The following table shows the details of each indicated error.

6-3-2

Slice I/O Terminal Error History

The DeviceNet Configurator can read the error history details of the most
recent errors that occurred in the Slice I/O Terminal.

Error History Tab 
Page

Error name

Contents

Error processing

Saved in error 

history when 

power goes OFF?

Connection 
Time Out

DeviceNet communications 
timeout

Generally, the error is caused by noise and commu-
nications are restored automatically. If the problem 
occurs frequently, check the following items.

• Is the baud rate the same as the Master’s?
• Are lengths of cables (trunk and branch lines) cor-

rect?

• Are cables short-circuited, broken, or loose?
• Is terminating resistance connected to both ends 

of the trunk line only?

• Is noise interference excessive?

Yes

Bus Off error 
detected

DeviceNet communications 
bus off

(Communications stopped 
because of too many data 
errors.)

Check the following items and restart the Slice I/O 
Terminal.

• Is the baud rate the same as the Master’s?
• Are lengths of cables (trunk and branch lines) cor-

rect?

• Are cables short-circuited, broken, or loose?
• Is terminating resistance connected to both ends 

of the trunk line only?

• Is noise interference excessive?

Yes

Node address 
duplication

There is a node address 
duplication error at another 
Unit in the DeviceNet network.

Set the node addresses again to eliminate the dupli-
cation, and restart the Slice I/O Terminal.

Yes

Summary of Contents for SMARTSLICE - 04-2008



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands