manualshive.com logo in svg

Omron SMARTSLICE - 04-2008, Operation Manual

Share
Download
Omron SMARTSLICE - 04-2008 Operation Manual Download Page 104

85

Using Another Company's Master Unit

Appendix B

Note

SET condition for MAC ID: MAC ID No. 64 to 99.

Assembly Object (0x04)

Object 
instance 

Attribute ID

Contents

Get 

(read) Set 

(write)

Value 

1

MAC ID

Yes

Yes

2

Baud rate

Yes

No

3

BOI

Yes

No

00 (hexadecimal)

4

Bus Off counter

Yes

No

5

Allocation information

Yes

No

6

MAC ID switch changed No

No

7

Baud rate switch 
changed 

No

No

8

MAC ID switch value 

No

No

9

Baud rate switch value 

No

No

Service

DeviceNet service

Parameter option 

0E

Get_Attribute_Single None

4B

Allocate_Master/
Slave_Connection_Set

None

4C

Release_Master/
Slave_Connection_Set 

None

Object class

Attribute 

Not supported 

Service 

Not supported 

Object instance

Attribute 

ID

Contents

Get (read) 

Set (write)

Value 

1

Number of members in 
list

No

No

2

Member list

No

No

3

Data

Yes

No

Service

DeviceNet service

Parameter option 

0E

Get_Attribute_Single None

Summary of Contents for SMARTSLICE - 04-2008



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands