manualshive.com logo in svg

Omron SMARTSLICE - 04-2008, Operation Manual

Share
Download
Omron SMARTSLICE - 04-2008 Operation Manual Download Page 68

49

Wiring DeviceNet Communications Cables

Section 3-3

The following connector is included with the Unit.

Note

GRT1-DRT Connector Compatibility
The following table classifies connectors in terms of compatibility with the
GRT1-DRT. Before using any connectors other than those shown here, check
for incompatibility related to structure or cables.

• Compatible Connectors

• Incompatible Connectors

• The following crimp terminals are recommended.

Phoenix Contact AI Series and A1 Series

Model

Specifications

Remarks

XW4G-05C4-TF-D

Multi-branch Parallel Clamp 
Connector with Screws

Provided with Unit.

Model

Specifications

Remarks

XW4B-05C1-H1-D

Parallel Connector with Screws

For node and T-branch tap connec-
tion. Connector screws provided. 

---

XW4B-05C1-VIR-D Orthogonal Connector with Screws

For node and T-branch tap connec-
tion. Connector screws provided. 

The cable comes 
out of the left side 
when viewed from 
the front of the 
Unit.

XW4G-05C1-H1-D

Parallel Clamp Connector with Screws

For node and T-branch tap connec-
tion. Connector screws provided. 

---

XW4G-05C4-TF-D

Multi-branch Parallel Clamp Connec-
tor with Screws

For multi-drop node connection. Con-
nector screws provided.

Provided with 
Unit.

Model

Specifications

Remarks

XW4B-05C4-TF-D

Multi-branch Parallel Connector with 
Screws

---

XW4B-05C4-T-D

Multi-branch Parallel Connector without 
Screws

Connector type

Cable type

XW4B-05C1-H1-D

XW4B-05C1-V1R-D

XW4G-05C1-H1-D
XW4G-05C4-TF-D

Crimp tool

Thin 
Cable

Signal line

AI 0.25-6YE

AI 0.25-8YE

CRIMPFOX
ZA3 
or 
CRIMPFOX
UD6

Power line

AI 0.5-6WH

AI 0.5-10WH

Thick 
Cable

Signal line

A1-6

A1-10

Power line

AI 2.5-8BU

AI 2.5-10BU

Summary of Contents for SMARTSLICE - 04-2008



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands