manualshive.com logo in svg

Omron SMARTSLICE - 04-2008, Operation Manual

Share
Download
Omron SMARTSLICE - 04-2008 Operation Manual Download Page 88

69

LED Indicators and Error Processing

Section 6-2

DeviceNet 
Communica-
tions Unit, 
continued

NS

Green

DeviceNet communications 
are normal.

---

---

Waiting for completion of node 
address duplication check.

If the problem occurs only in a particular 
Slave, check the baud rate and restart the 
Slave.

Red

There is a node address 
duplication error at another 
Unit in the DeviceNet network.

Set the node addresses again to eliminate 
the duplication, and restart the Slice I/O Ter-
minal.

DeviceNet communications 
stopped because of too many 
data errors.

Check the following items and restart the 
Slice I/O Terminal.

• Is the baud rate the same as the Master’s?
• Are lengths of cables (trunk and branch 

lines) correct?

• Are cables short-circuited, broken, or 

loose?

• Is terminating resistance connected to 

both ends of the trunk line only?

• Is noise interference excessive?

Red

DeviceNet communications 
timeout occurred.

Check the following items.

• Is the baud rate the same as the Master’s?
• Are lengths of cables (trunk and branch 

lines) correct?

• Are cables short-circuited, broken, or 

loose?

• Is terminating resistance connected to 

both ends of the trunk line only?

• Is noise interference excessive?

Green

Online with DeviceNet, but 
waiting for a connection with 
the Master.

Check whether the Master has started 
properly.

Check whether the Slice I/O Terminal is reg-
istered in the Master’s scan list.

Unit

LED 

name

Color

Status

Meaning

Likely cause of error

NS

NS

NS

NS

NS

Summary of Contents for SMARTSLICE - 04-2008



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands