manualshive.com logo in svg

Omron SMARTSLICE - 04-2008, Operation Manual

Share
Download
Omron SMARTSLICE - 04-2008 Operation Manual Download Page 69

50

Connecting the Turnback Cable

Section 3-4

3-3-2

Connecting to the DeviceNet Communications Unit

Align the DeviceNet Communications Unit connector with the cable connector,
and insert the cable connector fully into the DeviceNet Communications Unit
connector.

Always tighten the connector’s screws to a torque between 0.25 and 0.3 N-m
to secure the connector.

3-4

Connecting the Turnback Cable

When a Slice I/O Terminal is divided into blocks to expand the system, con-
nect a GRT1-TBR Right Turnback Unit to the GRT1-TBL Left Turnback Unit
with a GCN2-100 Turnback Cable.

Note

Power is not supplied through the GCN2-100 Turnback Cable. Always wire
(supply) the power to the GRT1-TBL Left Turnback Unit from the same power
supply that supplies the DeviceNet Communications Unit.

3-4-1

Connecting the Turnback Units

Connect the Turnback Units with a Turnback Cable, as shown in the following
diagram. A single DeviceNet Communications Unit can be expanded with up
to two additional blocks, connected with two sets of Turnback Units.

DeviceNet
Communications Unit

GRT1-TBR Turnback Unit

GRT1-TBL Turnback Unit

GCN2-100 Turnback Cable
Insert the cable's connector fully
until it clicks, which indicates that
the connector's top and bottom
latches have locked.

Summary of Contents for SMARTSLICE - 04-2008



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands