Omron SMARTSLICE - 04-2008 Operation Manual Download Page 17

Page: 17 / 122

xviii

Application Precautions

!Caution

The operating environment of the PLC System can have a large effect on the
longevity and reliability of the system. Improper operating environments can
lead to malfunction, failure, and other unforeseeable problems with the PLC
System. Be sure that the operating environment is within the specified condi-
tions at installation and remains within the specified conditions during the life
of the system.

Application Precautions

Observe the following precautions when using the DeviceNet Communica-
tions Unit.

• Fail-safe measures must be taken by the customer to ensure safety in the

event of incorrect, missing, or abnormal signals caused by broken signal
lines, momentary power interruptions, or other causes.

• Provide external interlock circuits, limit circuits, and other safety circuits in

addition to any provided within the PLC to ensure safety.

• Use the power supplies specified in the operation manuals.

• If the system is installed at a site with poor power supply conditions, take

appropriate measures to ensure that the power supply remains within the
rated voltage and frequency specifications.

• Provide circuit breakers and other safety measures to provide protection

against shorts in external wiring.

• Always ground the system to 100

Ω

or less when installing the system to

protect against electrical shock.

• Mount the PLC securely on DIN Track or with screws.

• Always turn OFF the power supply when mounting a DeviceNet Commu-

nications Unit.

• Always turn OFF the communications power supply and the power sup-

plies to the PLC and Slaves before attempting any of the following.

• Mounting or removing a Unit such as an I/O Unit, CPU Unit, Memory

Cassette, or Master Unit.

• Mounting or removing Remote I/O Terminal circuit sections.

• Assembling any devices or racks.

• Setting rotary switches.

• Connecting or wiring cables.

• Connecting or disconnecting connectors.

• Do not attempt to disassemble, repair, or modify any Units.

• Be sure that all the terminal screws are tightened to the torque specified

in the relevant manuals. Loose screws may cause fire, malfunction, or
damage the Unit.

• Be sure that all the mounting screws and cable connector screws are

tightened to the torque specified in the relevant manuals.

• Be sure that all the communications connector screws are tightened

securely. (The communications connector screw torque is 0.5 to 0.6 N•m.)

• Do not remove the label from a Unit before wiring. Always remove the

label after completing wiring, however, to ensure proper heat dispersion.

• Use the correct wiring components when wiring.

• Use crimp terminals for wiring. Do not connect bare stranded wires

directly to terminals.

• Double-check all wiring before turning ON the power supply.

Summary of Contents for SMARTSLICE - 04-2008



























































































































Search results

Summary of Contents for SMARTSLICE - 04-2008

Reviews:

Brands by name

Popular brands

Omron SMARTSLICE - 04-2008, Operation Manual

Search results

Summary of Contents for SMARTSLICE - 04-2008

Reviews:

Brands by name

Popular brands