manualshive.com logo in svg

Omron SMARTSLICE - 04-2008, Operation Manual

Share
Download
Omron SMARTSLICE - 04-2008 Operation Manual Download Page 66

47

Wiring DeviceNet Communications Cables

Section 3-3

Recommended Power 
Supplies

Use a SELV power supply with overcurrent protection.

A SELV power supply has redundant or increased insulation between the I/O,
an output voltage of 30 Vr.m.s and a 42.4-V peak or maximum of 60 VDC.

Recommended power supply: S82K-10024 (OMRON) or S8J-10024D
(OMRON)

Recommended Wire

Strip Length

Strip between 7 and 10 mm of insulation at the ends of the wires (stranded or
solid wire).

Pin Terminal Length

Use pin terminals with a pin (conductor) length of 8 to 10 mm.

3-3

Wiring DeviceNet Communications Cables

This section explains how to prepare the DeviceNet communications cables
that connect to the DeviceNet Communications Unit and how to attach com-
munications connectors.

For details on supplying the DeviceNet communications power and grounding
the DeviceNet Network, refer to the 

DeviceNet Operation Manual (W267)

.

3-3-1

Connecting Communications Cables 

Use the following procedure to prepare the communications cables and con-
nect them to the connectors. 

The same methods are used to connect the cables to connectors with and
without set screws. 

1,2,3...

1.

Remove about 30 to 80 mm of the cable covering, being careful not to dam-
age the mesh shield underneath. Do not remove more than necessary. Re-
moving excessive cable covering may cause a short-circuit. 

3.5 mm

0.6 mm

Side view

Front view

Type

Gauge

Stranded wire

20 AWG to 16 AWG
(0.5 to 1.25 mm

2

)

Solid wire

Pin terminal

Strip 7 to 10 mm.

Pin length: 8 to 10 mm

About 30 to 80 mm 
(Remove as little as possible.)

Summary of Contents for SMARTSLICE - 04-2008



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands