manualshive.com logo in svg

Omron SMARTSLICE - 04-2008, Operation Manual

Share
Download
Omron SMARTSLICE - 04-2008 Operation Manual Download Page 50

31

Unit Functions

Section 2-3

Note

The Unit conduction time monitor (Power ON time monitor) calculates the total
time that the Smart Slave's Network power supply is ON. The total time is not
calculated when the power is OFF. 

Setting Using the 
DeviceNet 
Configurator

The method used to set values from the DeviceNet Configurator (Ver. 2.43 or
later) is described here. 

1,2,3...

1.

Turn ON the DeviceNet Communications Unit's power supply.

2.

From the Main Window, open the Network Configuration Window and dou-
ble-click or click the right mouse button over the icon of the DeviceNet
Communications Unit to be set. Select 

Parameter

 and 

Edit

 to display the

Edit Device Parameters Window. 
From the Maintenance Mode Window, click the right mouse button over the
icon of the DeviceNet Communications Unit to be set. Select 

Parameter

and 

Edit

 to display the Edit Device Parameters Window. 

3.

Select the 

General

 Tab. 

4.

Enter the desired value in the 

Unit Conduction Time

 field. 

5.

Click the 

Download

 Button, and then click the 

Reset 

Button to reset the

Unit. 

6.

Click the 

OK

 Button.

Summary of Contents for SMARTSLICE - 04-2008



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands