manualshive.com logo in svg

Omron SMARTSLICE - 04-2008, Operation Manual

Share
Download
Omron SMARTSLICE - 04-2008 Operation Manual Download Page 11

xii

Application Considerations

SUITABILITY FOR USE 

OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the 
combination of products in the customer's application or use of the products. 

At the customer's request, OMRON will provide applicable third party certification documents identifying 
ratings and limitations of use that apply to the products. This information by itself is not sufficient for a 
complete determination of the suitability of the products in combination with the end product, machine, 
system, or other application or use.

The following are some examples of applications for which particular attention must be given. This is not 
intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses 
listed may be suitable for the products:

• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or 

uses not described in this manual.

• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical 

equipment, amusement machines, vehicles, safety equipment, and installations subject to separate 
industry or government regulations.

• Systems, machines, and equipment that could present a risk to life or property. 

Please know and observe all prohibitions of use applicable to the products.

NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR 
PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO 
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND 
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

PROGRAMMABLE PRODUCTS 

OMRON shall not be responsible for the user's programming of a programmable product, or any 
consequence thereof.

Summary of Contents for SMARTSLICE - 04-2008



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands